The Swap 2’s Pleasure-Cons appear to be working a lot better than the unique Swap, which suffered from stick drift points since its launch in 2017.
On the time of writing, there look like no widespread points with sticks breaking or drifting throughout gameplay.
Nonetheless, in some instances, you might want a alternative. Maybe unintentional injury prompted the keep on with cease working. Or perhaps you simply need to future-proof your console with Corridor Impact or TMR (Tunnel Magneto Resistance) alternate options. In any case, the stick makes use of related expertise to the unique Swap.
Both manner, this information will present you precisely take aside your Pleasure-Con 2 and substitute the analog sticks. Evidently, If you’re not assured in disassembling the controller, please seek the advice of an expert. that will help you. In any other case, give it a crack.
put together
The process for changing Pleasure-Con 2 sticks is nearly the identical for left and proper controllers. There are essential further steps you have to to carry out later utilizing the appropriate (crimson) Pleasure-Con. This might be clarified with particular steps and pictures.
Let’s get began what do you want:
- Alternative analog sticks (see finish of information for choices)
- Small Phillips (crosshead) screwdriver
- Small tri-wing (βYβ formed) driver
- A choose, plastic spudger, or small flathead screwdriver to assist pry up the Pleasure-Con case
- small tweezers
- Receptacle for safely storing small screws whereas working
After getting all the things sorted, you might be prepared to start out.
However a fast tip earlier than you begin: We suggest putting your screws and parts in your desk within the order you eliminated them. That is helpful for reassembly as you possibly can merely work backwards.
Let’s get began.
substitute Pleasure-Con 2 sticks
1. First, use a triangular screwdriver to take away the 2 small screws on the prime and backside of the blue strip.
When eradicating the screws, make sure that the screwdriver is “seated” appropriately, press down firmly and switch. Stripping the steel is straightforward, however the entire course of might be way more tough.
2. On the opposite aspect you should take away the plastic strip. Insert a choose into the opening slightly below the bumper and pry the highest of the strip off. Slide the choose down the aspect of the casing and gently pull it away from the controller.
3. You’ll be able to see two extra screws below the strip. One requires a tri-wing driver and the opposite a crosshead. Please delete these.
4. Whereas holding the case again in place, insert a choose into the small seam. Slide it down once more and gently take away it. Finally it is possible for you to to make use of your fingers to tug the quilt off, however do not pull on the quilt as you might injury the battery or make the motor wires sing.
5. Use your fingers to disconnect the rumble motor wires (blue and white), being cautious to not injury the wires together with your fingernails.
6. Disconnect the battery connector holding the crimson and black battery wires. We suggest utilizing tweezers right here, because the connector could also be too small to understand together with your fingers.
7. Take away the discharge button.
8. Insert a choose between the bumper button and the set off button and pry the set off towards you till it pops out.
9. Under the set off you possibly can see the bracket used to deal with the discharge button. Use a Phillips screwdriver to take away the 2 screws and pull off the bracket.
10. Use a Phillips screwdriver to take away the three screws that safe the midframe in place. Two of them are to the appropriate of the battery, and one is slightly below the bumper.
11. Pull out the bumper button.
12. You’ll be able to see the set off board above the battery. Take away one screw utilizing the crosshead. As soon as that is eliminated, slowly raise the board till it pops out. Due to the ribbon cable, it would keep linked for now.
13. Fastidiously take away your complete midframe together with your fingers.
14. Now take away the set off board. You will notice a locking flap that secures the ribbon cable in place. Raise this up and use tweezers or your fingers to softly take away the board.
15. Subsequent, do the identical with the ribbon cable that connects the analog sticks.
16. Use a Phillips screwdriver to take away the 5 screws to carry the mainboard in place.
17. That is the place the left and proper Pleasure-Con processes diverge.
17a. First, let’s check out the Pleasure-Con on the left (blue). Insert a spudger below the board and raise the board till you possibly can suit your finger below it. Raise the entire thing up a number of instances, being cautious to not injury the analog stick ribbon cable within the course of.
As you raise it up, you will see a chunk of black tape connecting the board and analog stick. Gently pry the board away from the analog stick, being cautious to not break it as you raise it.
There are two extra ribbon cables that hold the board linked. You do not have to take away these, however watch out to not wrinkle or break them.
17b. Now, it is the Pleasure-Con on the appropriate (crimson). The 2 ribbon cables I discussed earlier must be eliminated now as a result of their form prevents them from lifting the board. Raise each locking flaps and pull them out with tweezers. Now fully take away the board.
18. Use a Phillips screwdriver to take away the 2 screws that safe the analog stick. As soon as the stick is out, you possibly can take away it and insert a alternative.
19. Then, return to the steps on this information to reassemble your Pleasure-Con 2. Watch out when reconnecting the ribbon cable. Ensure that the locking flap is up after which put it again down after connecting the cables.
FAQ
The place can I get alternative Pleasure-Con 2 sticks?
There are fairly just a few choices out there on-line already, however I’ve solely used one to date, so that is what I like to recommend.
Gulikit TMR sticks can be found from Amazon within the UK and US on the following costs: Β£16.99 / $19.99. Like all TMR sticks, it makes use of a non-contact sensing technique. This implies there is no such thing as a friction between the supplies, minimizing the chance of future stick drift. It is usually stated to be extremely correct and energy environment friendly.
As for the usability, nicely…so far as we are able to inform, it is just about the identical as a daily Pleasure-Con 2 stick. That is type of what you need, proper? Watch out to not confuse them, as they give the impression of being the identical apart from the totally different colours of the ribbon cables.
Please word that some exterior hyperlinks on this web page are affiliate hyperlinks. This implies should you click on by way of and make a purchase order, we might obtain a small proportion of the sale. For extra data, please learn our FTC disclosure.
I went by way of the set up course of however the sticks and buttons do not work
Most likely simply one of many steps is fallacious. Do not panic!
Undergo the method step-by-step once more till you determine the issue. You’ll have forgotten to attach one of many ribbon cables, or it is probably not plugged in far sufficient.
All detailed steps are reversible until you fully destroy any element.
So what occurs should you fully break one thing?
Effectively, as I stated earlier, in case you are not assured in disassembling the Pleasure-Con 2, please don’t disassemble it. Please seek the advice of an knowledgeable.
Though this course of is less complicated than anticipated (although nonetheless scary), issues can nonetheless happen. It may be unwieldy and tough to fiddle with a lot of ribbon cables.
If the unique sticks do not work, shopping for a brand new set of Pleasure-Con 2 or Swap 2 controllers is a superbly viable possibility (albeit costly). Additionally keep in mind that in case your Pleasure-Con remains to be below guarantee, you possibly can have it repaired immediately by Nintendo.